ขอถามคำถามที่ค่อนข้างยากสักนิดนะครับ อีกไม่นาน คงมีใครอีกหลายคนได้ไรเฟิลใหม่ คำถามมีอยู่ว่า การทำ break in ลำกล้องไรเฟิลพี่ๆและผู้มีประสบการณ์ทุกท่าน ทำอย่างไรกันบ้างครับ ? จำเป็นไหม? และให้ผลดีอย่างไรบ้างครับ?
ผมค้นข้อมูลจากหลายที่ ได้วิธีการ break in ลำกล้องปืน m24 ที่แนะนำโดย Michael Haugen, แห่ง Remington milirary product ดังนี้ครับ
BARREL BREAK IN
The M24 comes from Remington ready to shoot, however it is recommended that the gun be broken in to enhance the life and accuracy of the weapon. Should you need to immediately employ or use the weapon you may disregard the break in procedure; however weapon life may suffer depending on how it is used. In order to break the weapon in follow the following steps;
1. Clear the weapon.
2. Remove the bolt.
3. Insert the bore guide.
4. Dry patch the barrel to remove any obstacles.
5. Remove the bore guide
6. Reinsert the bolt
7. Load one round
8. Fire one round
9. Clean the weapon (see ROUTINE MAINTENANCE)
10. Repeat this (firing 1 round and cleaning) until you have fired 10 rounds
11. Load and fire 3 rounds
12. Clean the weapon (see ROUTINE MAINTENANCE)
13. Repeat this another 9 times (10 iterations total) (firing 3 rounds and cleaning) for a total of 40 rounds being fired through the rifle (1 round x 10 and 3 rounds x 10)
14. Load and fire 5 rounds
15. Clean the weapon (see ROUTINE MAINTENANCE)
16. Repeat this another 9 times (10 iterations total) (firing 5 rounds and cleaning) for a total of 90 rounds being fired through the rifle (1 round x 10, 3 rounds x 10 and 5 rounds x 10)
17. Load and fire 10 rounds
18. Clean the weapon (see ROUTINE MAINTENANCE)
19. This should be 100 rounds total fired through the rifle, the M24 is now broken in.
หากทำตามนี้ทั้งหมดมีหวังจนครับ ราคาลูกบ้านขาต่างกับบ้านเรา สังเกตุว่าแกบอกว่า หากทำจะได้ยืดอายุลำกล้องและความแม่นยำครับ จริงเท็จประการไดโปรดแนะนำมือใหม่ด้วยครับ นอกจากนั้น ยังมีความคิดเห็นส่วนตัวอีกหลายท่านดังด้านล่างครับ
"About 30-40 rounds...
I don't believe in Barrel Break-In but it goes something like that:
1 shot then clean for around 5 rounds
3 shots then clean for 12-15 rounds
5 shots then clean for around 10-15 rounds.
I've never seen any difference between a barrel that had the Break-In procedure and a barrel that didn't.
So I simply stop doing it and it's 30 rounds that I can use for training.
If that makes you feel better, by all means, do it. "
"I do the barrel break in. On my 300WM, Bartlein barrel, it helped to reduce the copper fouling by the time I was finished and clean up was much faster at the end. Some barrels don't need it though, I have a couple Kriegers that never copper fouled badly from the get go so those I just shot. Depends on your barrel I think. Do it or don't, personal thing I guess. "
"I break in myself. I've done on the order of 14 barrels that way. To me it seems to clean up better after shooting. I do 1 shot at a time for 10 cleaning after each shot. Then 5 shots and clean. I do that twice. That equals 20 rounds down range. You're broke in. Use a good target and wait and see what it looks like. Put them all in the same point of aim. Some are pretty decent, considering what the barrel is going through."
"It builds character and teaches you patience . My Schneider slowly gained velocity as break in continued and cleaned up easily afterwards , My Lothar Walther took about 5 shots and the Rock was a 20 rounder with accuracy getting better as break in went on . If nothing else I felt better about it .
Factory barrels however take a Loooooong time and some that I have owned never really broke in . Your results may vary . "
บางท่านก็บอกว่าทำแล้วทำความสอาดง่ายขึ้น แม่นยำมากขึ้น แต่นั่นคือลำกล้อง match grade เช่น Schneider แล้งลำโรงงานละครับ
รบกวนสอบถามผู้รู้ทุกท่านครับ
ขอบคุณครับ
